[Aug 25, 2021] HPE6-A45 Dumps Full Questions - Exam Study Guide
Aruba Certified Switching Professional (ACSP) V1 Free Certification Exam Material from Actual4Labs with 170 Questions
NEW QUESTION 43
An AOS-Switch runs IGMP on A VLAN.
What is a requirement for the switch to be a potential IGMP querier on that VLAN?
- A. The switch must run PIM-SM or PIM-DM on that VLAN.
- B. The switch must have an IP address on that VLAN.
- C. The switch must have IGMP fast leave disabled globally.
- D. The switch must have at least one IGMP group configured on it manually.
Answer: B
Explanation:
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=c05207062
NEW QUESTION 44
Which switches can be deployed in a mesh topology for backplane stacking?
- A. Aruba 3810 switches
- B. Aruba 2920 switches
- C. Aruba 2930M switches
- D. Aruba 2930F switches
Answer: A
Explanation:
Reference: https://www.hpe.com/us/en/product-catalog/networking/networking-switches/pip.aruba-3810-switch-series.1008605435.html
NEW QUESTION 45
Refer to the exhibits.
Exhibit 1
Exhibit 2
In the exhibits, VLAN 20 under a device name indicates that the device is configured with that VLAN. The exhibits also indicate whether VLAN 20 is statically configured on each link, either as an untagged or a tagged VLAN. If the link has no label, VLAN 20 is not statically configured on that link.
A network administrator needs to deploy AOS-Switches that use port-based tunneled node. The plan calls for tunneled-node endpoints to be assigned to VLAN 20 and for the Aruba Mobility Controller to handle the tunneled-node traffic at Layer 2. Which exhibit shows the correct plan for VLAN 20 in the wired infrastructure?
- A. D
- B. C
- C. A
- D. B
Answer: D
NEW QUESTION 46
Refer to the exhibits.
Exhibit 1
Exhibit 2
Network administrators are alerted to high interface utilization on a switch by a management solution. They examine the utilization on the uplink interfaces several times an hour during problem times. The exhibit shows output typical of times of congestion. The administrators want to allocate bandwidth fairly and reduce congestion on the uplinks.
What could help meet these requirements?
- A. an outbound rate limit on interfaces 1 and 2
- B. an outbound rate limit on each edge port
- C. a per-queue rate limit on interfaces 1 and 2
- D. a broadcast rate limit on each edge port
Answer: D
NEW QUESTION 47
Refer to the exhibits.
Exhibit 1
Exhibit 2
Exhibit 2 shows IGMP groups on Switch-2, which runs IGMP but not PIM. Switch-1 and Switch-3 do not have IGMP or PIM enabled. Client 1 begins to forward multicasts to 239.1.1.1.
Which clients receive the multicasts?
- A. Client 2, Client 3, and Client 4
- B. Client 2, but not any of the other clients
- C. Client 3 and Client 4, but not Client 2
- D. Client 3, but not any of the other clients
Answer: C
NEW QUESTION 48
A network administrator needs to configure PIM across several AOS-Switches in the same routing domain.
What correctly describes how they can implement PIM modes?
- A. All switches must use PIM-DM only or all switches must use PIM-SM only for the solution to work.
- B. Switches at the network edge should run PIM-SM, while switches at the network core should run PIM-DM.
- C. Different interfaces on the same switch can run in different modes, but the mode must match the neighbor.
- D. Switches at the network core should run PIM-DM, while switches at the network edge should run PIM-SM.
Answer: A
NEW QUESTION 49
Refer to the exhibit.
An AOS-Switch has the ACL shown in the exhibit. A network administrator then enters these commands:
Switch(config)# mac-access-list standard myACL
Switch(config-std-macl)# deny 007d.45cc.0000 0000.0000.ffff
How does this ACL treat these frames:
1 = 007d.45cc.ffff 2 = 007d.45cc.0000
- A. It denies frame 1 and permits frame 2.
- B. It permits both frames.
- C. It denies both frames.
- D. It permits frame 1 and denies frame 2.
Answer: A
NEW QUESTION 50
The security plan for AOS-Switches requires protection from incoming malware traffic: generated from a worm-or virus-infected host.
Which feature should be implemented to provide the required protection?
- A. connection-rate filtering
- B. port security
- C. proxy ARP
- D. DHCP snooping
Answer: A
NEW QUESTION 51
Exhibit
An AOS-Switch has the ACL shown in the exhibit. A network administrator enters these commands:
How does this ACL treat these frames:
1 = 007d.45cc.ffff 2 = 007d.45cc.0000
- A. It denies frame 1 and permits frame 2.
- B. It permits both frames
- C. It permits frame 1 and denies frame 2.
- D. It denies both frames
Answer: A
NEW QUESTION 52
AOS-Switches authenticate guests to ClearPass with captive portal. An administrator notices that some guests are unable to reach the captive portal page. What will resolve this issue?
- A. Permit Allow All MAC-Auth on the CleatPass Portal.
- B. Permit DNS on the ClearPass Portal
- C. Permit HTTP or HTTPS on the ClearPass Portal.
- D. Permit DHCP on the ClearPass Portal.
Answer: B
NEW QUESTION 53
Refer to the exhibit.
Exhibit 1
Exhibit 2
Traffic between the servers in Area 1 takes a less optimal path rather than the link associated with VLAN
1000, subnet 10.0.0.0/30. Based on the exhibits, why is this the case?
- A. Switch-1 and Switch-2 cannot achieve adjacency on VLAN 1000 due to mismatches.
- B. OSPF routing switches choose the best intra-area routes based on Area 1 links only.
- C. The link between Switch-1 and Switch-2 has gone down.
- D. The metric on the VLAN 1000 interface is too low.
Answer: B
NEW QUESTION 54
Refer to the exhibits.
Exhibit 1.
Exhibit 2.
The company wants to minimize congestion on Link 1.
Which spanning tree implementation meets this goal?
- A. Instance 1 = VLANs 4,6 Instance 2 = VLANs 5,7Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1Switch 3 instance 1 priority = 1 Switch 3 instance 2 priority = 0
- B. Instance 1 = VLANs 4-5 Instance 2 = VLANs 6-7Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1Switch 3 instance 1 priority = 1 Switch 3 instance 2 priority = 0
- C. Instance 1 = VLANs 4,6 Instance 2 = VLANs 5,7Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1Switch 3 instance 1 priority = 0 Switch 3 instance 2 priority = 1
- D. Instance 1 = VLANs 4-5 Instance 2 = VLANs 6-7Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1Switch 3 instance 1 priority = 0 Switch 3 instance 2 priority = 1
Answer: C
NEW QUESTION 55
Refer to the exhibit.
AOS-Switches will enforce 802.1X authentication on edge ports. The company has two RADIUS servers, which are meant to provide redundancy and load sharing of requests.
The exhibit shows the planned RADIUS settings to deploy to the switches.
What should customers understand about this plan?
- A. AOS switches do not support two RADIUS servers for redundancy, instead, a secondary authentication method is required.
- B. Each RADIUS server must use a unique port number for the authentication and dynamic authorization port.
- C. Each AOS-Switch will send all RADIUS requests to the first server on the list unless that server becomes unreachable.
- D. Dynamic authentication is only permitted on one of the RADIUS servers and must be removed from the other.
Answer: C
NEW QUESTION 56
An AOS-Switch uses tunneled node. What is a best practice for the path between an AOS-Switch and its Mobility Controller?
- A. The path can support jumbo frames
- B. The path implements MACsec
- C. The path has a device that applies NAT
- D. The path crosses no VLAN boundaries
Answer: A
NEW QUESTION 57
Refer to the exhibit.
Endpoints in VLAN 2 connect directly to this switch. These devices should only be able to send DHCP, DNS, HTTP, and HTTPS traffic. However, they are able to send any traffic. Based on the exhibit, what is the issue?
- A. The ACL lacks a deny ip any any statement at the end.
- B. The switch does not have an IP address on VLAN 2.
- C. The ACL is applied in the wrong direction.
- D. The name of the ACL applied to VLAN 2 is incorrect.
Answer: D
NEW QUESTION 58
Refer to the exhibits.
Exhibit 1
Exhibit 2
A company does not require authentication for security, but AOS-Switches are set up to use local MAC authentication (LMA) to assign the correct VLAN and priority to IP phones. IP phones and computers belong to different VLANs. Each device is supposed to connect to a specific port, but sometimes users connect their devices to the wrong ports and cannot receive access without help from IT.
How can a network administrator configure the switches to eliminate this issue?
- A. Add the MAC addresses for computers to the myPhones MAC group.
- B. Apply LMA to all edge switch ports, and set the unauth VLAN to the user VLAN.
- C. Create a user role that applies the user VLAN, and set this role as the initial role.
- D. Set the address limit to 2 on the switch ports that apply LMA.
Answer: A
NEW QUESTION 59
Refer to the exhibit.
Switch-1 and Switch-2 are configured to provide VRRP in VLAN 2. Based on the output, what will happen when a client in VLAN 2 sends an ARP request for its default gateway IP address?
- A. Both Switch-1 and Switch-2 will respond, and each will respond with its own MAC Address.
- B. Only Switch-2 will respond, and it will respond with the virtual MAC address for VRID 2.
- C. Only Switch-2 will respond, and it will respond with its own MAC address.
- D. Both Switch-1 and Switch-2 will respond, and both will respond with the virtual MAC address for VRID 2.
Answer: B
NEW QUESTION 60
Refer to the exhibit.
Both Switch-1 and Switch-2 redistribute RIP routes into OSPF. The network administrator wants routers in Area 1 to receive the redistributed routes from Switch-1 but not from Switch-2.
What should the administrator do to achieve this goal?
- A. Configure a subnet range for Area 1 on Switch-2, and set the no-advertise option.
- B. Configure Area 1 as a stub area, with no summaries on Switch-2.
- C. Configure Area 1 as a Not So Stubby Area (NSSA) on all routing devices in Area 1.
- D. Configure Area 1 as a stub area, and import the routes with a low metric on Switch-2.
Answer: C
NEW QUESTION 61
Refer to the exhibits.
Exhibit 1
Exhibit 2
A network administrator sets up PIM-DM to route traffic from the multicast source to clients in VLAN 24. The server begins to forward multicasts, and the clients are set up to receive them. However, the multicasts do not reach the clients.
Based on the output, what should the administrator verify?
- A. that Switch-1 has selected Switch-2 as its RP for 239.1.1.1
- B. that state refreshes are enabled on Switch-2
- C. that Switch-2 has PIM-DM enabled on VLAN 10
- D. that VLAN 24 on Switch-1 runs both IGMP and PIM-DM
Answer: C
NEW QUESTION 62
Refer to the exhibit.
A network administrator sets up 802.1X authentication to a RADIUS server on an AOS-Switch. The RADIUS server and user devices are both set up to use PEAP MSCHAPv2. The administrator tests the authentication and sees the output shown in the exhibit. Which issue could cause this output?
- A. The switch port is set for user mode 802.1X, but the RADIUS server is set for port mode
- B. The administrator entered the wrong password for the test account
- C. The RADIUS shared secret does not match on the switch and the server
- D. The switch does not have a certificate for port-access installed on the switch
Answer: C
NEW QUESTION 63
What is a reason to implement PIM-DM as opposed to PIM-SM?
- A. to conserve bandwidth over WAN links
- B. to permit a higher density of rendevous point (RP) routers in the network core
- C. to control exactly which multicast groups are routed through the network
- D. to obtain the simplest setup in a network with high bandwidth
Answer: D
NEW QUESTION 64
Refer to the exhibit.
Why are these switches unable to achieve adjacency?
- A. The area range is incorrect on Switch-1 and missing on Switch-2.
- B. Switch-2 does not support every area that Switch-1 does.
- C. They have the same priority and cannot elect a Designated Router (DR).
- D. Switch-1 and Switch-2 use different area types for Area 1.
Answer: D
NEW QUESTION 65
Refer to the exhibits.
Exhibit 1
Exhibit 2
A company has attempted to implement OSPF without success. The devices in Area 1 need to be able to reach Area 2. Routes should be aggregated for advertisement in other areas. What must be changed to meet these requirements?
- A. Move the 10.1.0.0/16 range to Area 2 on Switch-1 and the 10.2.0.0/16 range to Area 1 on Switch-2.
- B. Add Area 1 and Area 2 on VLAN 100 on both Switch-1 and Switch-2. Remove Area 3.
- C. Add the 10.2.0.0/16 range on Switch-1 and the 10.1.0.0/16 range on Switch-2.
- D. Change Area 3 to Area 0; remove Area 1 from Switch-2 and Area 2 from Switch-1.
Answer: D
NEW QUESTION 66
Refer to the exhibit.
Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue. The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?
- A. mismatched IP addresses on the VLAN for the link
- B. a hardware issue, such as a broken cable
- C. asymmetric routing introduced by a routing configuration error
- D. an issue with queuing, caused by mismatched QoS settings
Answer: B
NEW QUESTION 67
What is the minimum requirement for a device to pass local MAC authentication (LMA) on an AOS-Switch?
- A. The device MAC address matches a MAC group, address, OUI, or range that is associated with an LMA profile.
- B. The device MAC address matches a default MAC group, which is enabled but not necessarily associated with a profile.
- C. The device MAC address matches a default MAC group that is associated with an LMA profile.
- D. The device MAC address matches a configured MAC group, address, OUI, or range, which is not necessarily associated with a profile.
Answer: A
Explanation:
Explanation/Reference:
NEW QUESTION 68
......
Dumps Brief Outline Of The HPE6-A45 Exam: https://www.actual4labs.com/HP/HPE6-A45-actual-exam-dumps.html