Exam Questions and Answers for 350-501 Study Guide Questions and Answers!
Implementing and Operating Cisco Service Provider Network Core Technologies Certification Sample Questions and Practice Exam
Cisco 350-501 certification exam is an essential exam for network engineers looking to advance their career in the service provider industry. 350-501 exam covers a wide range of topics and tests the candidate's ability to implement and operate Cisco's core technologies in a service provider network environment. Passing the exam will earn the candidate the Cisco Certified Specialist - Service Provider Core certification, which is a valuable credential in the industry.
NEW QUESTION # 62
Refer to the exhibit. P3 and PE4 are at the edge of the service provider core and serve as ABR routers Aggregation areas are on either side of the core.
Which statement about the architecture is true?
- A. If each area is running its own IGP. BGP must provide an end-to-end MPLS LSP
- B. To support seamless MPLS, the BGP route reflector feature must be disabled
- C. To support seamless MPLS. TDP must be used as the label protocol
- D. If each area is running its own IGP. the ABR routers must redistribute the IGP routing table into BGP
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9600/software/release/16-
12/configuration_guide/mpls/b_1612_mpls_9600_cg/configuring_seamless_mpls.html
NEW QUESTION # 63
Which additional feature does MPLS DiffServ tunneling support?
- A. using GRE tunnels to hide markings
- B. interaction between MPLS and IGP
- C. PHB layer management
- D. matching EXP and DSCP values
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_te_diffserv/configuration/15-mt/mp-te-diffserv-15-mt-book/mp-diffserv-tun-mode.html
NEW QUESTION # 64
Refer to the exhibit.
Guidelines
-
This is a lab item in which tasks will be performed on virtual devices.
* Refer to the Tasks tab to view the tasks for this lab item.
* Refer to the Topology tab to access the device console(s) and perform the tasks.
* Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
* All necessary preconfigurations have been applied.
* Do not change the enable password or hostname for any device.
* Save your configurations to NVRAM before moving to the next item.
* Click Next at the bottom of the screen to submit this lab and move to the next question.
* When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
-
R1 and R2 are having issues forming an eBGP neighbor relationship. Troubleshoot and resolve the issue to achieve these goals:
1. Configure R1 and R2 to form a BGP neighborship using their Loopback interfaces.
2. Form the neighbor relationship using a BGP multihop mechanism. Use minimal values to solve the issue.
Answer:
Explanation:
Here is the solution:
NEW QUESTION # 65
After implement MPLS protocol for multiple VRFs on a single Cisco device, the engineer notices all VRFs on the router still do to not LDP session protection feature enabled. Which configuration must the engineer apply to enable the LDP session protection feature FOR LDP neighbors within each VRF?
- A. Configure LDP session protection globally on the device only.
- B. Configure LDP session protection globally on the device and on each neighbor that requires session protection.
- C. Configure LDP session protection within the individual VRFs.
- D. Configure LDP session authentication on the device to enable LDP session protection on each VRF automatically.
Answer: C
NEW QUESTION # 66
Refer to the exhibit. After a networking team configured this MPLS topology, the supervisor wants to view MPLS labels to verify the path that packets take from router R1 to router R7 The team already Issued an ICMP ping to verify connectivity between the devices. Which task must the team perform to allow the supervisor to view the label switch path?
- A. Configure MPLS TE to display the labels in the stack between the head and tail-end routers
- B. Configure MPLS LDP Sync to sync labels from the routing table to the MPLS forwarding table.
- C. Implement MPLS OAM to display the labels for each hop along the path
- D. Implement MPLS LDP to assign labels to all the routes in the transit path.
Answer: C
NEW QUESTION # 67
What do Ansible and Salt Stack have in common?
- A. They both use DSL configuration language
- B. They both use YAML configuration language
- C. They both have agents running on the client machine
- D. They both can be designed with more than one master server
Answer: B
NEW QUESTION # 68
Which two IS-IS parameters must match before two Level 2 peers can form an adjacency? (Choose two )
- A. authentication settings
- B. MTU
- C. area ID
- D. hello timer setting
- E. system ID
Answer: A,B
NEW QUESTION # 69
Which two routing protocols support Cisco MPLS TE Tunnels? (Choose two.)
- A. IS-IS
- B. OSPF
- C. RIP
- D. BGP
- E. EIGRP
Answer: A,B
NEW QUESTION # 70
Refer to the exhibit:
This configuration is being applied on an IOS XR router.
Which statement about this configuration is true?
- A. It is used to enable gRPC
- B. It is used to create a streaming subscription with a 60-second interval
- C. It is used to set up configuration to poll network data
- D. It is used to create a streaming subscription with a 600-second interval
Answer: B
NEW QUESTION # 71 
Refer to the exhibit. A network engineer is implementing OSPF multiarea. Which command on interface G0/1 resolves adjacency issues in the new area?
- A. ip ospf network point-to-point
- B. ip ospf network broadcast
- C. ip ospf network non-broadcast
- D. ip ospf network point-to-multipoint
Answer: A
Explanation:
Section: Networking
Explanation/Reference:
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/118879-configure-ospf-
00.html#:~:text=When%20Multi%2DArea%20Adjacency%20is,which%20the%20ADJ%20is%20formed.
NEW QUESTION # 72
What are two characteristics of MPLS TE tunnels? (Choose two.)
- A. They are unidirectional.
- B. They are run over Ethernet cores only.
- C. They use RSVP to provide bandwidth for the tunnel.
- D. The headend and tailend routers of the tunnel must have a BGP relationship.
- E. They require EIGRP to be running in the core.
Answer: A,C
NEW QUESTION # 73
Refer to the exhibit. An engineer is preparing to implement link aggregation configuration.
Which statement al about this configuration is true?
- A. The switch port passively negotiates an EtherChannel if it receives PAgP packets from a connected peer
- B. The switch port negotiates an EtherChannel if it receives LACP packets from a connected peer
- C. The switch port actively sends packets to negotiate an EtherChannel using PAgP
- D. The switch port accepts LACP and PAgP packets from a connected peer and negotiate an EtherChannel using the common EtherChannel mode.
Answer: C
Explanation:
https://www.cisco.com/en/US/docs/switches/metro/me3600x_3800x/trash/swethchl.html
NEW QUESTION # 74
Refer to the exhibit:
Export statistics received do not include the BGP next hop.
Which statement about the NetFlow export statistics is true?
- A. To include the BGP next hop in the export statistics, those keywords must be included with the version
9 entry. - B. Loopback 0 must be participating in BGP for it to be included in the export statistics.
- C. The origin AS and the peer-as will be included in the export statistics.
- D. Only the origin AS of the source router will be included in the export statistics.
Answer: A
NEW QUESTION # 75
What causes multicast traffic to permanently stay on the shared tree and not switch to the source tree?
- A. The RP announcements are being filtered
- B. The SPT threshold is set to infinity
- C. SSM range is being used
- D. The RP IP address is configured incorrectly
Answer: A
Explanation:
Section: Services
NEW QUESTION # 76
Refer to the exhibit:
What does this value mean when it is received in XML?
- A. It indicates a break in a sequence
- B. It indicates a value assigned by a network administrator to tag a route
- C. It shows the ending of the script
- D. It means a data field is blank
Answer: D
NEW QUESTION # 77
Refer to the exhibit.
Which show command shows statistics for the control plane policy and is used to troubleshoot?
- A. show control-plane CoPP
- B. show policy-map control-plane
- C. show policy control-plane
- D. show control-plane
Answer: B
Explanation:
NEW QUESTION # 78 
Refer to the exhibit Router R1 and its peer R2 reside on the same subnet in the network. If an engineer implements this configuration to R1, how does it make connections to R2?
- A. R1 establishes UDP connections that are authenticated with a clear-text password.
- B. R1 establishes UDP connections that are authenticated with an MD5 password.
- C. R1 establishes TCP connections that are authenticated with a clear-text password.
- D. R1 establishes TCP connections that are authenticated with an MD5 password.
Answer: D
Explanation:
Section: Networking
NEW QUESTION # 79
Refer to the exhibit.
An engineer is configuring an administrative domain in the given multi-vendor environment with PIM-SM.
Which feature must the engineer implement so that devices will dynamically learn the RP?
- A. BSR
- B. BIDIR-PIM
- C. SSM
- D. Auto-RP
Answer: D
NEW QUESTION # 80
Refer to the exhibit:
Based on the show/ command output, which result m true after BGP session is established?
- A. The IOS XR router advertises and accepts all routes to and from eBGP neighbor 192.168.2.2
- B. The IOS XR router advertises all routes to the neighbor 192.168.2.2, but it does not accept any routes from 192.168.2.2
- C. The IOS XR router does not advertise any routes to the neighbor 192.168.2.2,but it accepts all routes from 192.168.2.2.
- D. No routes are accepted from the neighbor 192.168.2.2, nor are any routes advertised to it
Answer: D
NEW QUESTION # 81
A service provider is using QoS to manage customer traffic over the MPLS backbone.
Which three statements about the behavior of each MPLS QoS mode based on QoS policy in the service provider core are true? (Choose three.)
- A. Pipe mode changes the original CE IP packet markings.
- B. Uniform mode changes the original CE IP packet markings.
- C. Short-pipe mode does not change the original CE IP packet markings.
- D. Uniform mode does not change the original CE IP packet markings.
- E. Pipe mode does not change the original CE IP packet markings.
- F. Short-pipe mode changes the original CE IP packet markings.
Answer: B,C,E
NEW QUESTION # 82
......
350-501 certification dumps - CCNP Service Provider 350-501 guides - 100% valid: https://www.actual4labs.com/Cisco/350-501-actual-exam-dumps.html
100% Pass Your 350-501 at First Attempt with Actual4Labs: https://drive.google.com/open?id=17t7jT05l5dNg1Uc2u_w-Hh9GQI2w2Kxa